Skip Navigation

Your Environment. Your Health.

RNA Isolation Using The Qiagen RNEasy Midi Kit

RNA Isolation Using The Qiagen RNEasy Midi Kit

Animal Tissue Protocol*

*See the specialized protocol for heart, muscle and skin tissue.

For use of the midi columns, the weight of the tissue should be less than 150 mg. Even though the kit states, up to 250 mg of tissue may be used with the midi kit, it has been our experience that the yield of total RNA can be reduced due to column overloading, even when splitting the sample over 2 columns as we routinely do in the NMC. Read notes before proceeding with protocol. Tissues utilized in this protocol include liver, kidney, thymus, lung, prostate and ovary.

Tissue Preparation for Homogenization:
Tissue preparation for homogenization is done at room temperature under a hood.

  1. Lysis buffer is prepared by adding 10 μl beta-mercaptoethanol (ß-ME) per ml of RLT buffer. Four mls of ß-ME/RLT is required for each sample.
  2. Tissue is quickly weighed (>20-150 mg) and placed in a medium-sized weigh boat containing ß-ME/RLT buffer (1 ml) and minced using 2 sterile razor blades for tissue disruption.
  3. Pour the remaining ß-ME/RLT (3 ml) in a 15 ml round-bottom polypropylene tube (not provided). Add the minced sample and homogenize for a total of 60 seconds. (See tips for optimal homogenization.) Proceed to the next sample.
    RNA Extraction:
    All steps for the extraction of RNA are performed at room temperature. All centrifugations are carried out using a swinging bucket rotor at 4000 x g (the maximum speed of 3500-5000 rpm corresponds to 3000-5000 x g for most rotors). DNase treatment is recommended.
  4. After all the samples have been disrupted, centrifuge the tissue lysate for 5 min. Carefully pipette the supernatant (3.5 ml) into a new vessel (15-ml polypropylene tube, not provided). Make sure to place the pipet tip below the fatty upper layer, if present, and avoid pipetting the pellet at the bottom of the tube. Proceed to step 5.
  5. Add one volume (3.5 ml) of 70 % ethanol to the homogenized lysate. **For liver, use 50% ethanol.** For all other tissues use 70% ethanol. Shake vigorously by inverting the tube 8-10 times. If a visible precipitate forms, re-suspend the precipitate by vigorous shaking (inverting the tube 8-10 times) and immediately proceed to the next step.
  6. Split sample (3.5 ml) over 2 RNA easy midi spin columns sitting in a 15-ml centrifuge tubes (provided) and close the tube gently by placing the cap on top of the tube. Centrifuge for 10 min. Discard flow through. Reuse collection tube in step 7.
  7. Add 2 ml RW1 to column. Centrifuge 5 min. Discard flow-through. Reuse collection tube in step 8.
  8. Prepare DNase I (add 20μl DNase I stock solution to 140μl Buffer RDD for each sample), mix by inversion.
  9. Pipet 160μl DNase I directly on column membrane. Incubate RT, 15 min.
  10. Add 2 ml Buffer RW1 to the column and close the tube gently. Incubate RT, 5 min. Centrifuge for 5 min. to wash the column. Discard flow through. Reuse collection tube in step 8.
  11. Add 2.5 ml Buffer RPE to the column and close the tube gently. Centrifuge for 2 min. Discard flow through. Reuse collection tube in step 9.
  12. Add another 2.5 ml of Buffer RPE to the column and centrifuge for 10 min. to dry.
  13. To elute RNA transfer spin column to a new 15 ml collection tube (provided). Pipet 200μl of RNase-free water directly onto the column membrane. Close tube gently, let it stand for 1 min then centrifuge for 3 min
  14. Repeat step 10 as described with a second volume of RNase-free water. Gently mix and measure volume of eluate.
  15. Quantitate, concentrate – if necessary - and store RNA in a microcentrifuge tube at -70°C.

For Agilent Commercial Arrays:
Aliquots of 5μg should be stored at ~0.5μg/μl in RNase-free water and one aliquot of 5μl at ~200ng/μl for the BioAnalyzer.

This content is available to use on your website.
Please visit NIEHS Syndication to get started.